FTOOL - PUC-Riowebserver2.tecgraf.puc-rio.br/ftp_pub/users/lfm/ftool300tutorialframe.pdf · Ftool...

Click here to load reader

  • date post

    11-Mar-2020
  • Category

    Documents

  • view

    3
  • download

    0

Embed Size (px)

Transcript of FTOOL - PUC-Riowebserver2.tecgraf.puc-rio.br/ftp_pub/users/lfm/ftool300tutorialframe.pdf · Ftool...

  • Prof. Luiz Fernando Martha - PUC-Rio Rua Marquês de São Vicente, 225 - CEP 22453-900 - Rio de Janeiro, RJ Tel. +55 21 2512-5984 - Fax. +55 21 3527-1848 - E-mail: [email protected] - URL: http://www.tecgraf.puc-rio.br/~lfm

    FTOOL Tutorial for creation and analysis of a simple

    frame and result visualization

    Educational Version 3.00 August 2012

    http://www.tecgraf.puc-rio.br/ftool

    This file: http://www.tecgraf.puc-rio.br/ftp_pub/lfm/ftool300tutorialframe.pdf

    FTOOL model:

    http://www.tecgraf.puc-rio.br/ftp_pub/lfm/ftool300frame.ftl

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 2

    Users of this educational version are free to apply and re-distribute the program as they wish.

    However, neither the author nor the PUC-Rio University or any other related institution is

    responsible for the incorrect use of the program and its results. The author and PUC-Rio have no

    legal responsibility for any damage caused directly or indirectly to a person or a company, resulting

    from the application of any information or the utilization of the program. Users are responsible for

    all conclusions made through the program. There is no commitment of satisfactory performance or

    any kind of warranty.

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 3

    Table of Contents

    Create a file for plane frame model (command "Save as... ") ................................................................................... 4 Specification of units and number formatting ........................................................................................................... 4 Grid of coordinates and grid point spacing with attraction (snap) ............................................................................ 5 Insertion of first member........................................................................................................................................... 5 Insertion of second member ...................................................................................................................................... 6 Insertion of third member.......................................................................................................................................... 6 Insertion of horizontal dimension line....................................................................................................................... 7 Insertion of left vertical dimension line .................................................................................................................... 7 Insertion of right vertical dimension line .................................................................................................................. 8 Creation of new material ........................................................................................................................................... 8 Selection of material type and name ......................................................................................................................... 9 Assignment of created material to all members ........................................................................................................ 9 Verification of member parameters and attributes using mouse right button.......................................................... 10 Creation of new cross-section for beam member .................................................................................................... 10 Selection of welded I-shape (NBR standard) for beam member............................................................................. 11 Definition of specific welded I-shape and assignment to beam member ................................................................ 11 Selection of members by empty cross-section property set (NONE) ...................................................................... 12 Creation of new cross-section for column members ............................................................................................... 12 Selection of welded I-shape (NBR standard) for column members ........................................................................ 13 Definition of specific welded I-shape and assignment to column members ........................................................... 13 Definition of pin support and assignment to left inferior node ............................................................................... 14 Definition of fixed support and assignment to right inferior node .......................................................................... 14 Insertion of a hinge at right top node ...................................................................................................................... 15 Alternative: insertion of hinge at right end of beam member.................................................................................. 15 Member deformation constraints menu and fence selection of all members .......................................................... 16 Turn on shear deformation and assignment to selected members ........................................................................... 16 Creation of uniformly distributed force load for beam member.............................................................................. 17 Definition of value of uniformly distributed force load and assignment to beam member in local system ............ 17 Creation of linearly distributed force load for left column...................................................................................... 18 Definition of values of linearly distributed force load and assignment to right column member in global system 18 Salve complete model in the same created file (command "Save") ........................................................................ 19 Visualization of model deformed configuration response....................................................................................... 19 Visualization of model axial force diagram response ............................................................................................. 20 Visualization of model shear force diagram response............................................................................................. 20 Visualization of model bending moment diagram response.................................................................................... 21 Visualization of support reactions........................................................................................................................... 21

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 4

    Create a file for plane frame model (command "Save as... ")

    Specification of units and number formatting

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 5

    Grid of coordinates and grid point spacing with attraction (snap)

    Insertion of first member

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 6

    Insertion of second member

    Insertion of third member

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 7

    Insertion of horizontal dimension line

    Insertion of left vertical dimension line

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 8

    Insertion of right vertical dimension line

    Creation of new material

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 9

    Selection of material type and name

    Assignment of created material to all members

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 10

    Verification of member parameters and attributes using mouse right button

    Creation of new cross-section for beam member

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 11

    Selection of welded I-shape (NBR standard) for beam member

    Definition of specific welded I-shape and assignment to beam member

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 12

    Selection of members by empty cross-section property set (NONE)

    Creation of new cross-section for column members

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 13

    Selection of welded I-shape (NBR standard) for column members

    Definition of specific welded I-shape and assignment to column members

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 14

    Definition of pin support and assignment to left inferior node

    Definition of fixed support and assignment to right inferior node

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 15

    Insertion of a hinge at right top node

    Alternative: insertion of hinge at right end of beam member

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 16

    Member deformation constraints menu and fence selection of all members

    Turn on shear deformation and assignment to selected members

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 17

    Creation of uniformly distributed force load for beam member

    Definition of value of uniformly distributed force load and assignment to beam

    member in local system

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 18

    Creation of linearly distributed force load for left column

    Definition of values of linearly distributed force load and assignment to right

    column member in global system

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 19

    Salve complete model in the same created file (command "Save")

    Visualization of model deformed configuration response

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 20

    Visualization of model axial force diagram response

    Visualization of model shear force diagram response

  • Ftool – Version 3.00 Copyright Aug. 2012 – Luiz Fernando Martha

    Tutorial for creation and analysis of a simple frame and result visualization 21

    Visualization of model bending moment diagram response

    Visualization of support reactions