Tubo extruído/calibrado Bronce Br Características … · a Las tolerancias indicadas en esta...
Transcript of Tubo extruído/calibrado Bronce Br Características … · a Las tolerancias indicadas en esta...
www.bronmetal.com
Tubo extruído/calibrado Bronce Br
Características técnicas [ES]
Extruded tube/calibration Bronze Br
Technical Characteristics [EN]
Extrudé tube / calibré Bronze Br
Caracteristiques Tecniques: [FR]
Extrudierte Schlauch / Kalibrierung Bronze Br
Technische Daten [AL]
Bronce Br [ES]
Producto formato: Tubo extruído/calibrado [ES]
Características técnicas: Tubos de cobre extruído/calibrado redondos para aplicaciones decorativas [ES]
www.bronmetal.com
Bronce Br [ES]
Producto formato: Tubo extruído/calibrado [ES]
Características técnicas: Tubos de cobre extruído/calibrado redondos para
aplicaciones decorativas [ ES]
Bronce Br [ES]
Producto formato: Tubo extruído/calibrado [ES]
Características técnicas: Tubos de cobre extruído/calibrado redondos para aplicaciones decorativas [ES]
www.bronmetal.com
ALEACIONES
Designación del material Composición química en % (m/m) Densidad
g/cm3
Simbólica Numérica Elemento Cu Fe Ni P Pb Sn Zn Total otros aprox.
CuSn6 CW452K mín. Resto - - 0,01 - 5,5 - -
8,8 máx. - 0,1 0,2 0,4 0,02 7,0 0,2 0,2
CuSn8 CW453K mín. Resto - - 0,01 - 7,5 - -
8,8 máx. - 0,1 0,2 0,4 0,02 8,5 0,2 0,2
CuSn4Pb2P CW455K mín. Resto - - 0,2 1,5 3,5 - -
8,9 máx. - 0,1 0,2 0,4 2,5 4,5 0,3 0,2
CuSn8P CW459K mín. Resto - - 0,2 - 7,5 - -
8,8 máx. - 0,1 0,3 0,4 0,05 8,5 0,3 0,2
CuSn8PbP CW460K mín. Resto - - 0,2 0,1 7,5 - -
8,8 máx. - 0,1 0,3 0,4 0,5 9,0 0,3 0,2
Bronce Br [ES]
Producto formato: Tubo extruído/calibrado [ES]
Características técnicas: Tubos de cobre extruído/calibrado redondos para aplicaciones decorativas [ES]
www.bronmetal.com
CARACTERÍSTICAS MECÁNICAS
Designaciones Espesor de
pared Resistencia a la
tracción Límite elástico convencional
al 0,2% Alargamiento Dureza
Material
Estado metalúrgico
t Rm Rp0.2 A HV HB
Simbólica Numérica mm N/mm2 N/mm2 %
máx. mín. mín. máx. mín. mín. máx. mín. máx.
CuSn6
CW452K
M 20 - - - - - - - -
R340a 10 340 - 260 50 - - - -
H070a 10 - - - - 70 105 65 100
R400 5 400 220 - 30 - - - -
H105 5 - - - - 105 150 100 145
R490 3 490 390 - 10 - - - -
H140 3 - - - - 140 175 135 170
R580 2 580 500 - 5 - - - -
H170 2 - - - - 170 - 165 -
CuSn8
CW453K
M 20 - - - - - - - -
R380a 10 380 - 290 55 - - - -
H080a 10 - - - - 80 110 75 105
R450 5 450 250 - 25 - - - -
H115 5 - - - - 115 160 110 155
R520 3 520 440 - 10 - - - -
H155 3 - - - - 155 190 150 185
R590 2 590 520 - 5 - - - -
H180 2 - - - - 180 - 175 -
Bronce Br [ES]
Producto formato: Tubo extruído/calibrado [ES]
Características técnicas: Tubos de cobre extruído/calibrado redondos para aplicaciones decorativas [ES]
www.bronmetal.com
Designaciones Espesor de
pared Resistencia a la
tracción Límite elástico convencional
al 0,2% Alargamiento Dureza
Material
Estado metalúrgico
t Rm Rp0.2 A HV HB
Simbólica Numérica mm N/mm2 N/mm2 %
máx. mín. mín. máx. mín. mín. máx. mín. máx.
CuSn4Pb2P
CW455K
M 20 - - - - - - - -
R430 10 430 220 - 25 - - - -
H125 10 - - - - 125 155 120 150
R520 5 520 430 - 8 - - - -
H155 5 - - - - 155 - 150 -
CuSn8P CuSn8PbP
CW459K CW460K
M 20 - - - - - - - -
R460 10 460 280 - 30 - - - -
H130 10 - - - - 130 165 125 160
R550 5 550 480 - 12 - - - -
H165 5 - - - - 165 195 160 190
R620 3 620 540 - 5 - - - -
H180 3 - - - - 180 - 175 - a En el estado recocido. NOTA 1 - 1 N/mm2 equivale a 1 Mpa.
Bronce Br [ES]
Producto formato: Tubo extruído/calibrado [ES]
Características técnicas: Tubos de cobre extruído/calibrado redondos para aplicaciones decorativas [ES]
www.bronmetal.com
TOLERANCIAS
Diámetro nominal Tolerancias del diámetro medio
por encima de hasta e inclusive aplicable al diámetro medio Aplicable a cualquier diámetro incluidas las desviaciones de la forma
circular para las longitudes rectasa,b
3c 10 ± 0,06 ± 0,12
10 20 ± 0,08 ± 0,16
20 30 ± 0,12 ± 0,24
30 50 ± 0,15 ± 0,30
50 100 ± 0,20 ± 0,50
100 200 ± 0,50 ± 1,00
200 300 ± 0,75 ± 1,50
300 450 ± 1,00 ± 2,00
a Las tolerancias indicadas en esta columna no son aplicables a - tubos en rollos o bobinas - tubos con OD/T>50 - tubos en el estado recocido b Cuando el diámetro se mide a una distancia de los extremos del tubo de hasta 100mm o de la equivalente a un diámetro nominal (eligiendo el menor de ambos valores), salvo que se acuerde lo contrario, se admite incrementar la tolerancia multiplicándola por 3. c Incluido el 3.
Bronce Br [ES]
Producto formato: Tubo extruído/calibrado [ES]
Características técnicas: Tubos de cobre extruído/calibrado redondos para aplicaciones decorativas [ES]
www.bronmetal.com
Diámetro exterior nominal Tolerancias del espesor nominal de pared t (%)
mm t de 0,3 mm hasta 1 mm
inclusive t por encima de 1 mm hasta 3 mm inclusive
t por encima de 3 mm hasta 6 mm inclusive
t por encima de 6 mm hasta 10 mm inclusive
t por encima de 10mm por encima de hasta e inclusive
3a 40 ± 15 ± 13 ± 11 ± 10 -
40 120 ± 15 ± 13 ± 12 ± 11 ± 10
120 250 - ± 13 ± 13 ± 12 ± 11
250 450 - - ± 15 ± 15 ± 15 a Incluido 3.
TOLERANCIAS DEL DIÁMETRO INCLUIDA LA DESVIACIÓN DE LA FORMA CIRCULAR, TUBOS EN ROLLOS O BOBINAS
Diámetro exterior nominal Tolerancias del diámetro nominal incluida la desviación de la
forma circular Aplicable al diámetro interior de enrollamiento
por encima de hasta e inclusive
mín.
3a 6 ± 0,30 400
6 10 ± 0,50 600
10 20 ± 0,70 800
20 30 ± 0,90 1000
a Incluido 3.
Bronze Br [EN]
Product format: Extruded tube/calibration[EN]
Technical characteristics: Copper tubes extruded/calibration round for decorative applications [EN]
www.bronmetal.com
Bronze Br [EN]
Product format: Extruded tube/calibration [EN]
Technical characteristics: Copper tubes extruded/calibration round for
decorative applications [ EN]
Bronze Br [EN]
Product format: Extruded tube/calibration[EN]
Technical characteristics: Copper tubes extruded/calibration round for decorative applications [EN]
www.bronmetal.com
ALLOYS
Material designation Chemical composition in % (m/m) Density g/cm3
Symbol Numerical Element Cu Fe Ni P Pb Sn Zn Total others approx.
CuSn6 CW452K mín. Resto - - 0,01 - 5,5 - -
8,8 máx. - 0,1 0,2 0,4 0,02 7,0 0,2 0,2
CuSn8 CW453K mín. Resto - - 0,01 - 7,5 - -
8,8 máx. - 0,1 0,2 0,4 0,02 8,5 0,2 0,2
CuSn4Pb2P CW455K mín. Resto - - 0,2 1,5 3,5 - -
8,9 máx. - 0,1 0,2 0,4 2,5 4,5 0,3 0,2
CuSn8P CW459K mín. Resto - - 0,2 - 7,5 - -
8,8 máx. - 0,1 0,3 0,4 0,05 8,5 0,3 0,2
CuSn8PbP CW460K mín. Resto - - 0,2 0,1 7,5 - -
8,8 máx. - 0,1 0,3 0,4 0,5 9,0 0,3 0,2
Bronze Br [EN]
Product format: Extruded tube/calibration[EN]
Technical characteristics: Copper tubes extruded/calibration round for decorative applications [EN]
www.bronmetal.com
MECHANICAL CHARACTERISTICS
Designations Wall
thickness Tensile strength
Yield limit at 0.2% Enlogation Hardness
Material
Metallurgical state
t Rm Rp0.2 A HV HB
Symbol numerical mm N/mm2 N/mm2 %
máx. mín. mín. máx. mín. mín. máx. mín. máx.
CuSn6
CW452K
M 20 - - - - - - - -
R340a 10 340 - 260 50 - - - -
H070a 10 - - - - 70 105 65 100
R400 5 400 220 - 30 - - - -
H105 5 - - - - 105 150 100 145
R490 3 490 390 - 10 - - - -
H140 3 - - - - 140 175 135 170
R580 2 580 500 - 5 - - - -
H170 2 - - - - 170 - 165 -
CuSn8
CW453K
M 20 - - - - - - - -
R380a 10 380 - 290 55 - - - -
H080a 10 - - - - 80 110 75 105
R450 5 450 250 - 25 - - - -
H115 5 - - - - 115 160 110 155
R520 3 520 440 - 10 - - - -
H155 3 - - - - 155 190 150 185
R590 2 590 520 - 5 - - - -
H180 2 - - - - 180 - 175 -
Bronze Br [EN]
Product format: Extruded tube/calibration[EN]
Technical characteristics: Copper tubes extruded/calibration round for decorative applications [EN]
www.bronmetal.com
Designations Wall
thickness Tensile strength
Yield limit at 0.2% Enlogation Hardness
Material
Metallurgical state
t Rm Rp0.2 A HV HB
Symbol Numerical mm N/mm2 N/mm2 %
máx. mín. mín. máx. mín. mín. máx. mín. máx.
CuSn4Pb2P
CW455K
M 20 - - - - - - - -
R430 10 430 220 - 25 - - - -
H125 10 - - - - 125 155 120 150
R520 5 520 430 - 8 - - - -
H155 5 - - - - 155 - 150 -
CuSn8P CuSn8PbP
CW459K CW460K
M 20 - - - - - - - -
R460 10 460 280 - 30 - - - -
H130 10 - - - - 130 165 125 160
R550 5 550 480 - 12 - - - -
H165 5 - - - - 165 195 160 190
R620 3 620 540 - 5 - - - -
H180 3 - - - - 180 - 175 - a In the annealed condition. NOTE 1 - 1 N/mm2 equal to 1 Mpa.
Bronze Br [EN]
Product format: Extruded tube/calibration[EN]
Technical characteristics: Copper tubes extruded/calibration round for decorative applications [EN]
www.bronmetal.com
TOLERANCES
Nominal diameter Mean diameter tolerances
Above to Up to and including Applicable to the average diameter Applicable to any diameter including the deviations from the circular shape
to the straight lengthsa,b
3c 10 ± 0,06 ± 0,12
10 20 ± 0,08 ± 0,16
20 30 ± 0,12 ± 0,24
30 50 ± 0,15 ± 0,30
50 100 ± 0,20 ± 0,50
100 200 ± 0,50 ± 1,00
200 300 ± 0,75 ± 1,50
300 450 ± 1,00 ± 2,00
a The tolerances given colimn does not apply to - Tubes in roll sor cois - Tubes with OD/T>50 - Tubes in the annealed condition b When the diameter is measured at a distance from the ends of the tuve up to 100mm or equal to a nominal diameter (by selecting the lesser of two values), unless stated otherwise, is supports by multiplying increase tolerance 3. c Including 3.
Bronze Br [EN]
Product format: Extruded tube/calibration[EN]
Technical characteristics: Copper tubes extruded/calibration round for decorative applications [EN]
www.bronmetal.com
Nominal outside diameter Tolerances of the nominal thickness t (%)
mm t of 0,3 mm to 1 mm
inclusive t above de 1 mm to 3
mm inclusive t above de 3 mm to 6
mm inclusive t above de 6 mm to 10
mm inclusive t above 10mm
Above Up to and including
3a 40 ± 15 ± 13 ± 11 ± 10 -
40 120 ± 15 ± 13 ± 12 ± 11 ± 10
120 250 - ± 13 ± 13 ± 12 ± 11
250 450 - - ± 15 ± 15 ± 15
a Including 3.
DIAMETER TOLERANCES INCLUDING THE DIVERSION OF THE CIRCULAR SHAPE, TUBES OR COILS ROLLS
Nominal outside diameter Tolerances including nominal diameter of the circular
shape deviation Applies to the inside diameter of winding
Above Up to and including
mín.
3a 6 ± 0,30 400
6 10 ± 0,50 600
10 20 ± 0,70 800
20 30 ± 0,90 1000
a Including 3.
Bornze Br [FR]
Le format du produit: Tube extrudé / calibré [FR]
Caracteristiques techniques: Extrudé en tube de cuivre / caliber tour pour des applications décoratives [FR]
www.bronmetal.com
Bronze Br [FR]
Le format du produit: Tube extrudé / calibré [FR]
Caracteristiques tecniques: Extrudé en tube de cuivre / calibré tour des
applications décoratives [FR]
Bornze Br [FR]
Le format du produit: Tube extrudé / calibré [FR]
Caracteristiques techniques: Extrudé en tube de cuivre / caliber tour pour des applications décoratives [FR]
www.bronmetal.com
ALLIAGE
Désignation de la matière Composition en % (fraction massique) Densité g/cm3
Symbolique Numérique Èlément Cu Fe Ni P Pb Sn Zn Total autres approx.
CuSn6 CW452K mín. Reste - - 0,01 - 5,5 - -
8,8 máx. - 0,1 0,2 0,4 0,02 7,0 0,2 0,2
CuSn8 CW453K mín. Reste - - 0,01 - 7,5 - -
8,8 máx. - 0,1 0,2 0,4 0,02 8,5 0,2 0,2
CuSn4Pb2P CW455K mín. Reste - - 0,2 1,5 3,5 - -
8,9 máx. - 0,1 0,2 0,4 2,5 4,5 0,3 0,2
CuSn8P CW459K mín. Reste - - 0,2 - 7,5 - -
8,8 máx. - 0,1 0,3 0,4 0,05 8,5 0,3 0,2
CuSn8PbP CW460K mín. Reste - - 0,2 0,1 7,5 - -
8,8 máx. - 0,1 0,3 0,4 0,5 9,0 0,3 0,2
Bornze Br [FR]
Le format du produit: Tube extrudé / calibré [FR]
Caracteristiques techniques: Extrudé en tube de cuivre / caliber tour pour des applications décoratives [FR]
www.bronmetal.com
CARACTERISTIQUES MECANIQUES
Désignations Épaisseur du
mur Résistance à la
traction Limite èlastique
conventionnelle à 0.2% Allongement Durété
Matériau
Ètat métallurgique
t Rm Rp0.2 A HV HB
Symbolique Numérique mm N/mm2 N/mm2 %
máx. mín. mín. máx. mín. mín. máx. mín. máx.
CuSn6
CW452K
M 20 - - - - - - - -
R340a 10 340 - 260 50 - - - -
H070a 10 - - - - 70 105 65 100
R400 5 400 220 - 30 - - - -
H105 5 - - - - 105 150 100 145
R490 3 490 390 - 10 - - - -
H140 3 - - - - 140 175 135 170
R580 2 580 500 - 5 - - - -
H170 2 - - - - 170 - 165 -
CuSn8
CW453K
M 20 - - - - - - - -
R380a 10 380 - 290 55 - - - -
H080a 10 - - - - 80 110 75 105
R450 5 450 250 - 25 - - - -
H115 5 - - - - 115 160 110 155
R520 3 520 440 - 10 - - - -
H155 3 - - - - 155 190 150 185
R590 2 590 520 - 5 - - - -
H180 2 - - - - 180 - 175 -
Bornze Br [FR]
Le format du produit: Tube extrudé / calibré [FR]
Caracteristiques techniques: Extrudé en tube de cuivre / caliber tour pour des applications décoratives [FR]
www.bronmetal.com
Désignations Épaisseur du
mur Résistance à la
traction Limite èlastique
conventionnelle à 0.2% Allongement Durété
Matériau
Ètat métallurgique
t Rm Rp0.2 A HV HB
Symbolique Numérique mm N/mm2 N/mm2 %
máx. mín. mín. máx. mín. mín. máx. mín. máx.
CuSn4Pb2P
CW455K
M 20 - - - - - - - -
R430 10 430 220 - 25 - - - -
H125 10 - - - - 125 155 120 150
R520 5 520 430 - 8 - - - -
H155 5 - - - - 155 - 150 -
CuSn8P CuSn8PbP
CW459K CW460K
M 20 - - - - - - - -
R460 10 460 280 - 30 - - - -
H130 10 - - - - 130 165 125 160
R550 5 550 480 - 12 - - - -
H165 5 - - - - 165 195 160 190
R620 3 620 540 - 5 - - - -
H180 3 - - - - 180 - 175 -
a Dans l`état recuit NOTE - 1 N/mm2 équivalent à 1 Mpa.
Bornze Br [FR]
Le format du produit: Tube extrudé / calibré [FR]
Caracteristiques techniques: Extrudé en tube de cuivre / caliber tour pour des applications décoratives [FR]
www.bronmetal.com
TOLERANCES
Diamètre nominal Moyenne des tolerances de diamètre
Supérieur à Jusqu´à inclus Applicable au diameter moyen Applicable à n´importe quel diamètre, y compris les ècarts par rapport à la
forme circulaire aux longueus droites a,b
3c 10 ± 0,06 ± 0,12
10 20 ± 0,08 ± 0,16
20 30 ± 0,12 ± 0,24
30 50 ± 0,15 ± 0,30
50 100 ± 0,20 ± 0,50
100 200 ± 0,50 ± 1,00
200 300 ± 0,75 ± 1,50
300 450 ± 1,00 ± 2,00
a Les tolérances indiquèes dans cette colonne ne s`applique pas aux: - tubes en rouleaux ou en bobines - tubes à OD/T>50 - tubes à l`état recuit b Lorsque le diamètre est mesuré à une distance des extrémités du tuve jusqu`à 100mm ou égale à un diamètre nominal (en sélectionnant les deux moins de valeurs), sauf indication contraire, est soutenu par multipliant 3 à accroitre la tolèrance c Inclus le 3.
Bornze Br [FR]
Le format du produit: Tube extrudé / calibré [FR]
Caracteristiques techniques: Extrudé en tube de cuivre / caliber tour pour des applications décoratives [FR]
www.bronmetal.com
Le diameter nominal extérieur Tolérances de la t épaisseur de paroi nominale (%)
mm de 0,3 jusqu´à 1 inclus
t dessus de 1 mm à 3
mm inclus t dessus de 3 mm à 6
mm inclus t dessus de 6 mm à 10
mm inclus
t au-dessus de 10mm
Supérieur à Supérieur à Jusqu´à inclus
3a 40 ± 15 ± 13 ± 11 ± 10 -
40 120 ± 15 ± 13 ± 12 ± 11 ± 10
120 250 - ± 13 ± 13 ± 12 ± 11
250 450 - - ± 15 ± 15 ± 15
a Inclus 3.
TOLÉRANCES DE DIAMÉTRE Y COMPRIS LE DÉTOURNEMENT DE LA FORME CIRCULAIRE, TUBES OU ROLLS BOBINES
Le diameter nominal extérieur Tolerances y compris diamtétre nominal de l`écart de
forme circulaire Applicable au diamètre intèrieur de
l`enroulement
Supérieur à Jusqu´à inclus
mín.
3a 6 ± 0,30 400
6 10 ± 0,50 600
10 20 ± 0,70 800
20 30 ± 0,90 1000
a Inclus 3.
Bronze Br [AL]
Produkt format: Platte [AL]
Technische Daten: Gerollte Bronze-Platten für dekorative [AL]
www.bronmetal.com
Bronze Br [AL]
Produkt format: Extrudierte Schlauch / Kalibrierung [AL]
Technische daten: Extrudierte Kupferrohr / kalibriert Runde für
dekorative Anwendungen [ AL]
Bronze Br [AL]
Produkt format: Platte [AL]
Technische Daten: Gerollte Bronze-Platten für dekorative [AL]
www.bronmetal.com
LEGIERUNGEN
Werkstoffbezeichnung Zusammensetzung in % (Massenanteile) Dichte g/cm3
Kurzzeichen Nummer Element Cu Fe Ni P Pb Sn Zn Sonstige
insgesamt ungefähr
CuSn6 CW452K mín. Rest - - 0,01 - 5,5 - -
8,8 máx. - 0,1 0,2 0,4 0,02 7,0 0,2 0,2
CuSn8 CW453K mín. Rest - - 0,01 - 7,5 - -
8,8 máx. - 0,1 0,2 0,4 0,02 8,5 0,2 0,2
CuSn4Pb2P CW455K mín. Rest - - 0,2 1,5 3,5 - -
8,9 máx. - 0,1 0,2 0,4 2,5 4,5 0,3 0,2
CuSn8P CW459K mín. Rest - - 0,2 - 7,5 - -
8,8 máx. - 0,1 0,3 0,4 0,05 8,5 0,3 0,2
CuSn8PbP CW460K mín. Rest - - 0,2 0,1 7,5 - -
8,8 máx. - 0,1 0,3 0,4 0,5 9,0 0,3 0,2
Bronze Br [AL]
Produkt format: Platte [AL]
Technische Daten: Gerollte Bronze-Platten für dekorative [AL]
www.bronmetal.com
MECHANISCHE EIGENSCHAFTEN
Bezeichnung Wanddicke Zugfestigkeit 0,2% - Dehngrenze Dehnung Härte
Werkstoff
Zustand
t Rm Rp0.2 A HV HB
Kurzzeichen Nummer mm N/mm2 N/mm2 %
máx. mín. mín. máx. mín. mín. máx. mín. máx.
CuSn6
CW452K
M 20 - - - - - - - -
R340a 10 340 - 260 50 - - - -
H070a 10 - - - - 70 105 65 100
R400 5 400 220 - 30 - - - -
H105 5 - - - - 105 150 100 145
R490 3 490 390 - 10 - - - -
H140 3 - - - - 140 175 135 170
R580 2 580 500 - 5 - - - -
H170 2 - - - - 170 - 165 -
CuSn8
CW453K
M 20 - - - - - - - -
R380a 10 380 - 290 55 - - - -
H080a 10 - - - - 80 110 75 105
R450 5 450 250 - 25 - - - -
H115 5 - - - - 115 160 110 155
R520 3 520 440 - 10 - - - -
H155 3 - - - - 155 190 150 185
R590 2 590 520 - 5 - - - -
H180 2 - - - - 180 - 175 -
Bronze Br [AL]
Produkt format: Platte [AL]
Technische Daten: Gerollte Bronze-Platten für dekorative [AL]
www.bronmetal.com
Bezeichnung Wanddicke Zugfestigkeit 0,2% - Dehngrenze Dehnung Härte
Werkstoff
Zustand
t Rm Rp0.2 A HV HB
Kurzzeichen Nummer mm N/mm2 N/mm2 %
máx. mín. mín. máx. mín. mín. máx. mín. máx.
CuSn4Pb2P
CW455K
M 20 - - - - - - - -
R430 10 430 220 - 25 - - - -
H125 10 - - - - 125 155 120 150
R520 5 520 430 - 8 - - - -
H155 5 - - - - 155 - 150 -
CuSn8P CuSn8PbP
CW459K CW460K
M 20 - - - - - - - -
R460 10 460 280 - 30 - - - -
H130 10 - - - - 130 165 125 160
R550 5 550 480 - 12 - - - -
H165 5 - - - - 165 195 160 190
R620 3 620 540 - 5 - - - -
H180 3 - - - - 180 - 175 -
a Geglühter Zustand. ANMERKUNG 1 - 1 N/mm2 entspricht 1 Mpa.
Bronze Br [AL]
Produkt format: Platte [AL]
Technische Daten: Gerollte Bronze-Platten für dekorative [AL]
www.bronmetal.com
TOLERANCIAS
Dicke ( Nennmaß) Mittiere Durchmesser-Tolreanzen
von bis Für den mittleren Durchmesser Für jeden Durchmesser einschließlich der Abweichungen von der Kreisform zu den
geraden Längena,b
3c 10 ± 0,06 ± 0,12
10 20 ± 0,08 ± 0,16
20 30 ± 0,12 ± 0,24
30 50 ± 0,15 ± 0,30
50 100 ± 0,20 ± 0,50
100 200 ± 0,50 ± 1,00
200 300 ± 0,75 ± 1,50
300 450 ± 1,00 ± 2,00
a von Toleranzen in dieser Spalte angegeben nicht für - Rohre in Rollen oder Spulen - Rohre mit OD/T>50 - Rohre im geglühten Zustand b Wenn der Durchmesser in einem Abstand von den enden des Rohres bis zu 100 mm gemessen oder gleich einem Nenndurchmesser (Wahl des kleineren der beiden Werte), sofem nicht anders vereinbart, darf die toleranz mit 3 multipliziert erhöhen. c Inkulsive 3.
Bronze Br [AL]
Produkt format: Platte [AL]
Technische Daten: Gerollte Bronze-Platten für dekorative [AL]
www.bronmetal.com
Dicke ( Nennmaß) Grenzabmaße für die Dicke für Breitenª (Nennmaß)
mm
t von 0,3 mm bis 1 mm t von 1 mm bis 3 mm t von 3 mm bis 6 mm t von 6 mm bis 10 mm t oben 10mm von Bis
3a 40 ± 15 ± 13 ± 11 ± 10 -
40 120 ± 15 ± 13 ± 12 ± 11 ± 10
120 250 - ± 13 ± 13 ± 12 ± 11
250 450 - - ± 15 ± 15 ± 15
a Inklusive 3.
DURCHMESSERTOLERANZEN EINSCHIESSLICH DIE UMLEITUNG DES KREISFORM, ROHRE ODER ROHRSCHLANGEN ROLLS
Dicke ( Nennmaß) Nennweite Toleranzeweichung einschließlich kreisförmigen Anwendbar auf dem Innendurchmesser der
Wicklung
von Bis
mín.
3a 6 ± 0,30 400
6 10 ± 0,50 600
10 20 ± 0,70 800
20 30 ± 0,90 1000
a Incluido 3.