Turbine Flow Meter KOT SERIES · 2018-01-15 · Turbine Flow Meter 인천비전기업 /...

24
Turbine Flow Meter 인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체 (주) 플 로 우 닉 스 T E L : 82-32-579-2999 E-MAIL : [email protected] - 1 - KOT-F KOT-F (SUS BOX) KOT-F (SHIP PART) KOT-N (4~20mA) KOT-F (PULSE) KOT 터빈유량계는 전자부분과 기계부분이 조합된 제품이며 체적식 유량계입니다. 원리는 흐르는 유체속에 축차 (회전각)가 유량에 비례적으로 회전, 속도가 증감합니다. 이 축차의 회전수를 픽업 코일이 감지하여 전기적 신호 (주파수)로 변화시켜서 현장 지시, 적산을 활성화시킵니다. 이 유량계의 축과 저널베어링은 텅스텐재질이고 유체의 종류에 따라서는 스테인레스 재질의 볼 베어링이 적용됩니다. 산업전반에 걸친 분야, 과학연구 등 유량 측정과 시 스템 제어에 광범위하게 사용되어집니다. These flow meters are electromechanical, volumetric flow meters. The rotating angle increases in proportion to the flow rate. The rotate rate is detected by the pick-up coil and converted into electrical signal, activating local indicating totalizer. The flow meter's pole and journal bearings are manufactured with tungsten, and stainless steel ball bearings and are applied according to the variety of the fluid. 사양 (Specification) Turndown Ratio : 10:1 Flow Accuracy : ± 1% (@Liquid F.S), ± 1.5% (@Gas F.S) MFR STD' Repeatability : ± 0.1% Linearity : ± 0.1% Pressure Rating : 5000 psi (Maximum) Turbine Temperature : -30 C ~100 C (Option -90 C ~ 170 C) End Connection : (NPT, PT), (JIS 10K, JIS 20K Flange), Etc. KOT SERIES ■ 구조 (Structure) 및 치수 (Dimension) Size L(mm) 6A 120 10A 120 15A 120 20A 120 25A 120 32A 160 40A 160 50A 170 65A 200 80A 230 100A 240 125A 240 150A 330 200A 390 KOT-F 250A 450

Transcript of Turbine Flow Meter KOT SERIES · 2018-01-15 · Turbine Flow Meter 인천비전기업 /...

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 1 -

KOT-F KOT-F (SUS BOX) KOT-F (SHIP PART) KOT-N (4~20mA) KOT-F (PULSE)

KOT 터빈유량계는 전자부분과 기계부분이 조합된 제품이며 체적식 유량계입니다. 원리는 흐르는 유체속에 축차

(회전각)가 유량에 비례적으로 회전, 속도가 증감합니다. 이 축차의 회전수를 픽업 코일이 감지하여 전기적 신호

(주파수)로 변화시켜서 현장 지시, 적산을 활성화시킵니다. 이 유량계의 축과 저널베어링은 텅스텐재질이고 유체의

종류에 따라서는 스테인레스 재질의 볼 베어링이 적용됩니다. 산업전반에 걸친 분야, 과학연구 등 유량 측정과 시

스템 제어에 광범위하게 사용되어집니다.

These flow meters are electromechanical, volumetric flow meters. The rotating angle increases in proportion

to the flow rate. The rotate rate is detected by the pick-up coil and converted into electrical signal,

activating local indicating totalizer. The flow meter's pole and journal bearings are manufactured with

tungsten, and stainless steel ball bearings and are applied according to the variety of the fluid.

■ 사양 (Specification)

■ Turndown Ratio : 10:1 ■ Flow Accuracy : ± 1% (@Liquid F.S), ± 1.5% (@Gas F.S) MFR STD'

■ Repeatability : ± 0.1%

■ Linearity : ± 0.1%

■ Pressure Rating : 5000 psi (Maximum)

■ Turbine Temperature : -30 〬 C ~100 〬 C (Option -90 〬 C ~ 170 〬 C)

■ End Connection : (NPT, PT), (JIS 10K, JIS 20K Flange), Etc.

KOT SERIES

■ 구조 (Structure) 및 치수 (Dimension)

Size L(mm)

6A 120

10A 120

15A 120

20A 120

25A 120

32A 160

40A 160

50A 170

65A 200

80A 230

100A 240

125A 240

150A 330

200A 390

KOT-F 250A 450

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 2 -

KOT Code Description

FluidL LIQUID

G GAS

Connection

Size

6 6mm (pipe screw thread G3/8")

10 10mm (pipe screw thread G1/2")

15 15mm (pipe screw thread G1")

25 25mm (pipe screw thread G1-1/4")

32 32mm (flange type)

40 40mm (flange type)

50 50mm (flange type)

65 65mm (flange type)

80 80mm (flange type)

100 100mm (flange type)

125 125mm (flange type)

150 150mm (flange type)

200 200mm (flange type)

250 250mm (flange type)

Connection

Type

F Flange

N Screw

S Sanitary Ferrule

Material

B SS304

C SS316

D SS316L

X PTFE / Special

Indicator InstallC Compact

S Separator

Power

TAAC Power / Local(Flow Rate & Totalizer) & 4~20mA.DC

/ Pulse

TDDC Power 4-WIRE / Local(Flow Rate & Totalizer) & 4~20mA.DC

/ Pulse

B Local Indication Totalizer (Battery Type)

LP DC 24V (2-Wire, Loop Powered)

Output & Comunication Protocol

R1 1-Dry Contact

R2 2-Dry Contact

A Only 4~20mA.DC

P Only Pulse

R RS 485

Option

NH 비방폭형 (Non-Explosion)

Ex 방폭형 (Explosion-Proof Type)

ST Strainer (Y형)

■ Model Code

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 3 -

■ 유량범위 (Flow Rate Table)

Size

LiquidGas

(@ATM. AMB)Size

Liquid Gas

Flow Rate

(m3/h)

Flow Rate

(L/min)

Flow Rate

(N㎥/h)

Flow Rate

(m3/h)

Flow Rate

(L/min)

Flow Rate

(N㎥/h)

2A 30 ~ 160(L/h) 0.5 ~ 2.67 - 50A 4 ~ 40 50 ~ 50016 ~ 160

65A 7 ~ 70 67 ~ 7504A 40 ~ 250(L/h) 0.67 ~ 4.17 -

80A 10 ~ 100 167 ~ 1667 35 ~ 3506A 100 ~ 600(L/h) 1.67 ~ 10 -

100A 20 ~ 200 334 ~ 333450 ~ 500

10A 0.2 ~ 1.2 3.33 ~ 20 -

125A 20 ~ 250 334 ~ 416715A 0.6 ~ 6 10 ~ 100

1.5 ~ 7.5150A 30 ~ 300 500 ~ 5000 100 ~ 100020A 0.6 ~ 7.2 10 ~ 120

25A 1.0 ~ 10 16 ~ 167

4 ~ 40

200A 50 ~ 500 834 ~ 8334 170 ~ 1700

250A 80 ~ 800 1334 ~ 13334 250 ~ 250032A 1.5 ~ 15 20 ~ 250

40A 1.8 ~ 20 30 ~ 350 8 ~ 80

■ Notice

■ 보관지점은 반드시 아래 조건을 구비해야한다. (Place keeps that must satisfy conditions as below.)

a) 방수, 방습 (Water-proof, Moisture-proof)

b) 기계진동이 작고 부딪혀 충격 받는 것을 피해야 한다.

Machine vibration must not be great, and prevent damage from bump.

c) 온도는 -30 ~ +60℃. 이상적인 온도는 25℃ 내외이다.

Keep temperature at -30 ~ +60℃. Ideal temperature is around 25℃.

d) 만약 실외에 오랜 기간 보관한다면 유량계의 성능은 영향을 받는다. 그러므로 실내 보관이 아니라면 가급적

바로 설치하는 것이 좋다.

Efficiency of flowmeter immediately receives influence if it is kept outside during long times. Thus,

flowmeter must be installed as soon as possible after it is delivered.

■ 설치지점을 선택하는데 반드시 주의해야할 사항 (Notice for installation)

유량계의 설계는 이미 열악한 환경 조건하에서의 상황을 고려하였다. 그러나 장기적으로 그 정확도와 안정

성을 유지하지 위해서는 설치지점을 선택할 시에 반드시 아래사항을 주의해야 한다.

Flowmeter was designed with considering inferior environmental conditions. However, user must notice

following articles when deciding place of installation to keep its accuracy and stability for long time.

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 4 -

a) 주변온도: 주변온도변화가 매우 심한 장소에 설치하는 것은 피해야한다. 만약 주변 설비의 열복사를 받지

않도록 하고 송풍, 환풍이 원활한 지점을 선택해야 한다.

Environmental temperature : Keep away from any place that has large change of environmental

temperature. If a device receives thermal radiation, user must keep it away from heat, and take any

action of ventilation.

b) 주변공기: 유량계를 부식성기체가 있는 환경 중에 설치하는 것을 피해야 한다. 만약 이러한 환경 중

에 설치해야 한다면 반드시 송풍, 환풍이 원활하도록 조치를 취해야 한다.

Environmental air: Keep away from any place that has corrosive gas. If this product must be installed

in this environment, user must provide any action of ventilation to it.

c) 기계진동과 충격: 유량계의 구조가 매우 견고하나 설치장소를 선택할 때 가급적 기계의 진동 혹은 충격을

받을 수 있는 장소는 피해야 한다. 만약 유량계를 비교적 진동이 큰 배관에 설치해야 한다면 배관을

지탱하여 진동으로부터의 영향을 최소화해야 한다.

Mechanical vibration and impact : Structure of flowmeter is very solid, but user must keep away from

mechanical vibration or damage from bump when deciding the place of installation, if it is possible.

If a meter is installed on a pipe with relatively great vibration, user must support a pipe.

*기타 : 설치와 유지보수 및 수리를 위하여 유량계 설치 장소에 반드시 충분한 공간이 있어야 한다.

Others : Must be enough space around installation place of flowmeter , maintenance, and repair.

■ 휴대용 무선 전화기, 무전기를 사용시 주의 사항

(Notice for limited use of wireless electric transceiver.)

유량계의 전자부분은 고주파의 방해에 영향을 방지하도록 설계되어 있으나 만약 유량계에 너무 가까운 곳에서

무선전화기, 무전기를 송수신한다면 고주파의 노이즈가 영향을 미칠 수 있다. 만약 필요에 따라 사용해야

한다면 사전에 유량계 설치장소에서 무선전화기, 무전기의 영향을 받는지를 점검 후 사용하도록 한다. 일정한

간격으로 유량계를 향해 이동하면서 영향을 받는지 여부를 점검한다. 만약 영향을 받는다면 영향을 미치지

않는 거리를 두고 사용하도록 한다.

Electronic part of flowmeter can block the interruption by high frequency electric noise. However, if

wireless electric transceiver is used in any place too close to flowmeter, interruption by high frequency

noise can have influence on flowmeter. Investigate the influence of wireless electric transceiver on

flowmeter, and its installed location(Check influence with moving wireless electric transceiver toward

flowmeter from place some meters away). If it receives influence, keep the transceiver away from that

place immediately.

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 5 -

■ 방폭형 유량계를 설치할 때 주의해야할 사항 (Notice for installing explosion proof type flowmeter)

유량계의 설계는 “폭발성 환경용 전기 설비 통용 요구(GB3836.1)”,“폭발성 환경용 폭발 방지 전기 설비 격폭

발형 전기 설비"d""및 ”폭발성 환경용 폭발 방지 전기설비 본질 안전형 전로와 전기 설비“i"”,“ 표준이 규정

한 바의 1구역과 2구역의 위험지역”에 사용할 수 있다.

Flowmeter was designed to be used for “common demands of electric facilities for explosive

environment(GB3836.1)”,“explosion preventative electric facilities for explosive environment and remote

explosive electric facilities "d"", ”nature of explosion preventative electric facilities for explosive

environment, stabilized converter, and electric facilities“i"”, and “danger zone in area 1 and 2 regulated

by the standard”.

■ 구조와 작동 원리 (Structure and operation principle)

∎ 터빈유량 감응신호장치의 기본구조 (Basic structure of turbine induced signal device)

감응신호장치의 기본구조는 아래 그림과 같다. 그것은 본체, 정방향 프레임, 터어빈날개, 역방향 프레임, 압력

프레임과 증폭기를 가진 픽업센서 등으로 구성되어있다.

Basic structure of induced signal device is as shown in below. It is composed of cover body,

frame leading forward, disc, frame leading backward, pressure frame, and induced electricity switch.

∎ 작동 원리 (Operation principle)

감응신호장치(픽업센서)와 자력으로 연결된 본체의 터어빈 날개가 유체에 의한 운동에너지의 힘으로 회전을

하며, 날개는 주기적으로 유도전기 감응시스템의 기저항값을 변화시키고, 코일을 통한 자력 선속은 주기적으

로 변화가 일어나서 전기 펄스신호를 발생시키며, 증폭기를 통해 확대하여 유량 변환기에서 그에 상응하는 유

량값으로 변환, PLC 또는 다른 지시계에 출력을 통해 유량값을 비례적으로 전송하며, 순시유량과 적산량의

측정을 가능하게 한다.

When measuring induced path signal device(pickup sensor) by fluid, disc in induced signal device spins

by employing the force of dynamic energy of fluid, disc changes original resistance value of induced

electricity system periodically, magnetic flux through coil creates electric pulse signal owing to

periodical change, then it is transmitted to corresponding flow accumulative meter, PLC, or upper digit

calculator after expanding amplifier, and progresses to measure flow or total amount.

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 6 -

Size

(A)

Flow range

Fluid

Temp.

Pressure

(barG)

Ambient

temp.

Relative

temp.

Max

pressure

loss

(mbar)

Basic error limit

0.2%

Basic error limit

0.5%

Basic error limit

1%

min. max. min. max. min. max.

2 0.03 0.16

-20~80

6.3

-20~55 ⪳80

0.15

4 0.04 0.25 0.12

6 0.1 0.6 0.1 0.66.3

16

25

32"

0.08

10 0.25 1.2 0.2 1.2 0.05

15 1.2 6 0.6 4 0.6 6

0.03525 2 10 1.6 10 1 10

40 4 20 3 20 2 20

16

25

0.025

50 6 40 4 40 4 40

65 6 45 4 45 4 45

80 16 100 10 100 10 100

100 25 160 20 160 20 200

16

25

125 30 250 20 250 20 250

150 50 300 40 300 30 300

200 150 750 100 600 50 500

250 200 800 160 800 80 800 16

■ 기술 성능 (Technical efficiency)

∎ 터빈유량 감응 신호 장치의 기술 성능 (Efficiency of turbine flow induced signal device)

터빈 유량 감응 신호 장치의 수직 지름 ,유량 범위, 유체 온도/압력, 상대온도, 최대 압력손실은 표1.을 참조.

Refer to table for nominal vertical diameter, flow range, fluid temperature, nominal pressure, relative

temperature, and maximum pressure loss of turbine flow induced signal device.

Table 1.

∎ 리튬건전지 방식 Battery type (Power supply from lithium battery)

- 정확도 (Accuracy) :

순시 유량 (Flow rate) : 0.5% of water conduction

적산량 (Total flow) : 0.1% of water conduction

- 주변 온도 범위 (Ambient temperature range) : -20 ~ 55℃

- 사용 온도 범위 (Medium temperature range) : -20 ~ 80℃

- 방폭 온도에 근거하여 각 해당의 유체 온도를 결정한다.

Decide medium temperature in each group on the basis of explosion proof temperature.

- 습도환경 : 상대습도 5~100% (결로현상이 없는 장소 선택)

Environmental humidity : relative humidity 5~100% (frostiness is not acceptable)

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 7 -

- 유량 변환기 외함 재질 : 알루미늄합금 재료

Material of transmitter housing : aluminium alloy

- 전원 : 3.6V 리튬 전지 (연속 사용시 수명 : 2~3년)

Power : 3.6V lithium battery (Life times : 1~3 years)

- 지시 : 6자리 LCD 및 유량측정 단위 지시

Display : 6-digit LCD Type and engineering unit display

- 유량(%), 순간유량, 적산유량등 6가지의 지시 방식이 있다.

Flow(%), flowrate, and accumulated flow has 6 coupling types of display

- 출력 (Outputs) : 기능 없음 (None)

- 저장기능 : 정전시 모든 데이터는 저장된다.

Memory function : All data is reserved when power is off

- 오차수정 : 5지점(4단계)로 나누어 수정

Error correction : Correct by dividing into 5 points(4 grades)

- 보호 등급 : IP65, 방수, 먼지방지

Protection class : IP65, water-proof, dust-proof

- 방폭 등급(Enclosure Class) : Explosion proof Ex ib I or Ex dHBT4

- 무게 (Weight) : 1.5 kg

∎ 전원 공급 방식 (AC. DC Power supply type)

- 순간 유량 : 도수의 0.5% (Flowrate : 0.5% of water conduction)

- 누계 유량 : 도수의 0.1% (Accumulated flow : 0.1% of water conduction)

- 주변 온도 : -20 ~ 55℃ (Environmental temperature : -20 ~ 55℃)

- 유체 온도 : -30 ~ 80℃, 고온은 문의 바람 (Medium temperature : -30 ~ 80℃)

- 방폭 온도에 근거하여 각 해당의 유체 온도를 결정한다.

Decide medium temperature in each group on the basis of explosion proof temperature

- 습도환경 : 상대습도 5~100% (결로현상이 없는 장소 선택)

Environmental humidity : relative humidity 5~100%(frostiness is not acceptable)

- 유량 변환기 외함 재질 : 알루미늄합금 재료

Material of transmitter housing : aluminium alloy

- 전원 (Power supply) : AC 250V, 50~60Hz, DC24V(4-Wire), DC24V(2-wire loop powered)

- 지시 : 6자리 LCD 및 유량측정 단위 지시

Display : 6-digit LCD Type and engineering unit display

- 유량(%), 순간유량, 적산유량등 6가지의 지시 방식이 있다.

Flow(%), flowrate, and accumulated flow has 6 coupling types of display

- 출력 (Outputs) : 4~20mA.DC & pulse

- 저장기능 : 정전시 모든 데이터는 저장된다.

Memory function : All data is reserved when power is off

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 8 -

- 오차수정: 단을 나누어 수정

Error correction: Correct by dividing grade

- 보호 등급 : IP65, 방수, 먼지방지

Protection class : IP65, water-proof, dust-proof

- 방폭 등급(Enclosure Class) : Explosion proof Ex ib I or Ex dHBT4

- 무게 (Weight) : 1.8 kg

■ 설치 (Installation)

∎ 설치 장소 (Place of Installation)

감응신호장치(픽업센서)의 사용 온도, 즉 측정 액체의 사용 온도는 기본 -20 ~ +80℃(그 이상의 온도 적용은

당사에 문의 바람)이며, 주변의 상대 습도는 80% 이하의 조건이다. 유지보수가 용이한 장소로 설치를 고려해

야 하며, 유량계의 탈,부착이 가능한 곳과 배관진동과 배관의 응력 영향이 없는 장소에 설치하도록 한다.

증폭기에 외란 방지를 위해 강한 열복사와 방사성의 영향을 받지 않도록 한다. 그리고 외부로부터의

강력한 전자기에 의해 코일에 영향을 주지 않도록 반드시 고려해서 설치한다. 만약 불가피하게 그러한 장소에

설치해야할 경우 감응신호장치의 증폭기 외부에 강력한 전자기를 차폐할 수 있는 덮개를 부가적으로 설치해야

한다. 그렇지 않으면 변환기의 정상 작업(예를 들면 유량 지시와 출력의 오동작)에 심각한 영향을 줄 수 있다.

Install in condition that liquid temperature measured by induced signal device is –20~+80℃,

standard(high temperature available, consult our factory), and relatively humidity is lower than80%.

Install in any place with considering easy installation, piping vibration, or influence of stress. If it is

possible, avoid strong thermal radiation and influence of radioactivity. Simultaneously avoid the

influence that external strong electromagnetic field has on inspecting and measuring coil. If it is not

possible, put a cover on amplifier of electric induced device, if not, transmitter will receive serious

influence in normal operation.

∎ 설치 위치 (Location of Installation)

감응신호장치는 일반적으로 수평설치를 해야 하며, 설치시 유량계 본체에 표시된 흐름 방향의 화살표를 유체

의 유동 방향과 서로 부합되게 해야 한다. 수직배관에 설치를 해야 하는 경우 유체의 유동 방향을 아래에서

위로 흐르게 하여 측정 지점에서 유체가 만수 상태로 측정될 수 있도록 해야 한다.

Induced signal device generally should be installed horizontally, and an arrow of flow direction on

turbine flowmetert must meet the flow direction of fluid each other when installing. If it must be

installed vertically, make fluid flow upward from bottom to guarantee that fluid can be fully filled in

flow induced signal device.

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 9 -

- Reducer pipe: L=15D

- Connecting to single bent pipe: L=20D

- Connecting to double bent pipes

L=20D (one plane)

L=20D (two planes)

- Connecting to right-angled curved pipe:

L=20D

- If there is finishing valve

L=20D (all valves are full-opened)

L=50D (all valves are semi-opened)

∎ 배관 요점 (Points of Piping)

- 액체의 와류 현상과 유속이 고르지 않음을 제거하기 위해 유량계의 전단, 후단에 직관부 혹은 정류기

를 고려해야 한다. 일반적으로 상류부분(유량계 전단)의 직관부 길이는 10 ~ 20D(D는 배관의 구경), 하류부

분(유량계 후단)의 직관부 길이는 5D이며, 직관부는 축관이나 확관이 아닌 유량계의 관경과 일치해야 한다.

그렇지 않으면 측정의 오차가 발생하게 된다.

Arrange straight pipe section or rectifier in inlet of induced signal device to remove uneven vortex

and flow velocity of fluid. Generally, the length of straight pipe section in upstream area(inlet) is

15~20D(D is the nominal diameter of flowmeter). The length of straight pipe section in

downstream(outlet) is 5D, and the diameter of straight pipe section and the nominal diameter of

flowmeter must be the same each other. If not, there can be any error(reducer pipe or expander

pipe).

straight pipe section in upstream and downstream area

또한, 더욱 효율적인 와류 제거를 위하고 유량측량의 정밀도를 높이려면 상류부분(유량계 전단)의 직관부에

파이프로 구성된 정류기를 배치해야 한다. 정류기 상류부분의 직관부 길이는 10 ~ 20D이다.

Also if measured precision is increased to remove parasitic electricity more effectively, rectifier made

up with pipe in straight pipe section in upstream area can be introduced. The length of straight pipe

section installed in upstream area of rectifier is 10~20D.

- 유체중의 불순물을 제거하기 위해 유량계의 정상 동작 요소를 확보해야 하며 유량계의 수명을 높여야 한다.

유량계의 상류부분에 3~9 neck/cm²의 여과기를 설치할 것을 권장 한다. 일반적으로 배관경의 대소 여부와

여과기의 여과성능(조밀성)은 밀접한 관계가 있다. (배관경이 작아질수록 조밀해진다.) 유량계의 정상 동작을

보장하기 위해서는 여과기의 조밀성을 선별 사용하여야 한다.

Induced signal device must be normally operated, and it must have long life to remove impurities in

fluid. Filter with 3~9 neck/cm² must be installed on pipe line of induced signal device. If vertical

diameter is greater in general condition, the number of neck is rare, and if vertical diameter is

smaller, the number of necks is dense. User must selectively use the number of filter necks to ensure

normal operation of induced signal device on the basis of actual situation.

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 10 -

Mixture of air separator and filter(공기분리) Rectifier(정류기)

- 유량계의 연결부 용접 작업시, 반드시 파이프 내부에 돌출된 부분이 없어야 한다. 용접된 플랜지나 피팅류와

유량계 본체와의 둘레는 일치하는 것이 좋다. 한쪽으로 치우치거나 매끄럽지 않으면 유속이 고르지 못하게

분포하는 현상으로 유량계를 올바르게 사용할 수 없다.

When welding connection of flowmeter, there must be no projected part in pipe. When it is

connected to flange or fitting for thread, external diameter of two welded parts must be perfectly

same, and inner parts must not be exposed in pipe. If it is connected to different diameter, velocity

can be unevenly distributed. Thus, it cannot be used.

- 유지보수 또는 수리가 용이할 수 있도록 유량계 설치 지점의 전후 배관에 밸브를 설치하고 우회 배관을

설치해야 한다. 유량 제어용 밸브는 유량계의 하류부분(후단)에 설치해야 한다. 유량계의 유량 측정시 상

류부분(전단)에 설치한 밸브는 반드시 완전 개방하여 유체의 와류현상을 방지해야 한다.

Install cutting valve(finishing valve) on pipe at upstream and downstream side of flowmeter and install

bypass at the same time to ensure the necessity of inspection and repair under operation condition.

Flow control valve must be installed in downstream of flowmeter. When using flowmeter, finishing

valve installed in upstream must be opened to prevent fluid in upstream from parasitic

phenomenon.

- 지나치게 큰 유량이 감응신호장치를 통과할 때, 즉 유량범위의 상한선을 초과하게 되면 베어링은 과도한 속

도변화로 인해 급속하게 마모가 촉진된다. 따라서 과도한 유량이 예상될 경우는 사전에 하류부분에 설치된

밸브를 이용하여 유량을 조절해야 한다.

When fluid passed through induced signal device is too large(exceed over the maximum of flow

range), bearing promotes to be worn down if the change of its velocity is too large. Accordingly,

when calculating any potential situation of overflow in advance, fluid flow can be controlled with flow

control valve installed in downstream area.

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 11 -

KOTS Series의 로터는 유체의 운동에너지에 비

례하여 회전한다. 이 때 발생되는 펄스는 K 팩

터와 출력 신호로 활용할 수 있다.

The rotor is turned by the fluid force in flow

proportional way. A hall generator supplies

pulses, which can be utilized for digital or

analogue signal processing.

The generated pulses are specified as the

k-factor.

KOTS Code Description

FluidL LIQUID

G GAS

Connection

Size

8 1/4” (N)PT (FEMALE)

10 3/8” (N)PT (FEMALE)

15 1/2” (N)PT (FEMALE)

20 3/4” (N)PT (FEMALE)

Connection

Type

F Flange

N Screw

S Sanitary Ferrule

Connection

Material

B SS304

C SS316

P PVC

X Special

Indicator InstallC Compact

S Separator

Power

TA AC Power / Local(Flow Rate & Totalizer) & 4~20mA.DC / Pulse

TDDC Power 4-WIRE / Local(Flow Rate & Totalizer) & 4~20mA.DC /

Pulse

B Local Indication Totalizer (Battery Type)

LP DC 24V (2-Wire, Loop Powered)

Output & Comunication Protocol

A Only 4~20mA.DC

P Only Pulse

R RS 485

OptionEx 방폭형 (Explosion-Proof Type)

ST Strainer (Y형)

KOTS SERIES

■ Model Code

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 12 -

Type (KOT Series) KOTS-7 KOTS-6 KOTS-5 KOTS-4 KOTS-3 KOTS-2 KOTS-1

Article no (standard) 167523 167512 167525 167513 167514 167515 167516

Article no (with cable) - 167522 - 167517 167519 - -

Measuring range L/min 2~35 1~25 1.5~25 1~15 0.50~7.5 1~10 0.5~5

K-Factor PPL* 700 1000 1000 2200 4600 3300 6900

Size (mm) 8 8 8 8 8 8 8

Material Grilamid TR55 (PA 12) Polyamid 12

Viscosity range 0.8 ~ 16 mm2/sec

Accuracy ±2% of value

Repeatability 0.50%

Temperature range(℃) -20 ~ 100

Operating pressure 25 bar max

Burst pressure 200 bar

Electrical connection AMP Faston 2,8 / 6,3 x 0.8mm

Power supply 5~24 VDC

Current consumption Ca. 8mA

Output signal Pulses by open collector NPN

Pull-down resistor 1 ~ 2,2 k0hm

Connections Male threads 3/8"

Type KOTS-7 KOTS-6 KOTS-5 KOTS-4 KOTS-3 KOTS-2

1 L/min ~ 0 ~ 0 ~ 0 ~ 0 ~ 0 ~ 0

2 L/min ~ 0 ~ 0 0.05 ~ 0 0.06 ~ 0

5 L/min ~ 0 0.05 0.2 0.05 0.2 0.12

10 L/min ~ 0.12 0.17 0.4 0.2 0.7 0.4

15 L/min ~ 0.25 0.27 - 0.4 - 0.9

20 L/min ~ 0.45 0.48 - 0.7 - 1.3

25 L/min ~ 0.60 0.65 - - - -

30 L/min ~ 0.92 0.97 - - - -

■ 특징 (Features)

■ 저렴한 가격 (Low cost) ■ 소구경, 미소유량 측정에 적합 (Small size & low flow)

■ 쉽고 빠른 설치 (Easy and fast installation) ■ 용이한 유지보수 (Maintenance free)

■ 고압 배관에 적용 (High operating pressure) ■ 수평, 수직 배관 설치 (Installation in any position)

■ 기술 사양 (Technical Data)

* PPL = Pulses / liter Connections also available with cable

■ 압력 손실표 (Pressure drop table) (Unit : bar in water)

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 13 -

■ 구조 (Structure) 및 치수 (Dimension)

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 14 -

KOTQ Series는 온도와 압력 보상이 가능한 가스

터빈 유량계입니다.

Temperature and Pressure compensation,

normative flow can be displayed .

Application range Gas: Natural Gas, LPG, Air(1) Dry gas without water(2) Gas without corrosion

Measured Value

Primary measured value Flow Rate

Secondary measured value Volume flow

Tertiary measured value Temperature; Pressure (ONLY available for compensation model)

Features

Modular construction The measurement system consists of a flow sensor and a signal converter. It is available as compact and as separate version.

Compact version converter Compensation Type

D1: Local Display; 24V DC Power; Dual Power: Battery;4-20mAOutput(3-wire);SIRERS485

D2: Local Display: 24V DC Power; Dual Power: Battery;4-20mAOutput(2-wire);ModbusRS485

Connection Thread: DN25-DN50

Flange: DN25-DN300 (DIN, ANSI, JIS)

Measurement Ratio Standard – 10:1; Optional: 20:1

KOTGQ SERIES [Temperature and Pressure Compensation]

■ Technical Data

Measuring system

Design

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 15 -

Reference conditions Flow conditions similar to ISO 9951

Medium: Gas

Temperature: +10...+30°C / +50...+86°F

Inlet section: ≥ 10 DN

Operating pressure: 1 bar / 14.5 psig

Flow Meter Accuracy Standard: 1.5% Qmin to 0.2Qmax: 3%; 0.2Qmax to Qmax: 1.5%

Optional: 1.0% Qmin to 0.2Qmax: 2%; 0.2Qmax to Qmax: 1.0%

Temperature

Process temperature -20...+80°C

Ambient temperature(all versions)

Standard (with aluminum converter housing):

-10…+55°C

Storage temperature -20...+70°

Pressure

EN 1092-1 DN25…DN300: PN 16

Other pressures on request

ASME B16.5 1”...12": 150 lb RF

Other pressures on request

JIS 1”...12": 10 K

Other pressures on request

Installation For detailed information see chapter "Cautions for Installation"

Flow direction Forward

Arrow on flow sensor indicates flow direction.

Inlet run ≥ 10 DN

Outlet run ≥ 5 DN

Sensor housing SS304

Other materials on request

Flanges SS304

Other materials on request

Rotor ABS Plastic (Acrylonitrile - Butadiene – Styrene)

Aluminum Alloy

Bearings and Shaft SS304

Converter Housing Standard: polyurethane coated die-cast aluminum

Measuring accuracy

Operating conditions

Installation conditions

Materials

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 16 -

Model Suffix Code Description

KOTGQ-

Converter

D1-Local display; 24V DC and Battery Power; 3-wire 4-20mA OutputSURE RS485 Protocol

D2-Local display; 24V DC and Battery Power; 2-wire 4-20mA OutputModbus RS485 Communication

Diameter XXX

Three Digitals; for example:025: 25 mm; 050: 50 mm;125: 125 mm; 300: 300 mm

Flow rangeS(x) Refer to flow range table

W(x) Refer to flow range table

Body MaterialS SS304

L Cast Aluminum

Rotor MaterialS ABS Plastic

L Aluminum Alloy

Explosion LevelN Safety Field without Explosion

E1 ExiaIICT4

E2 ExdIIBT6

Connection

-DXX

DXX: D06, D10, D16, D25, D40D06: DIN PN6; D10: DIN PN10D16: DIN PN16; D25: DIN PN25D40: DIN PN40

-AXAX: A1, A3, A6A1: ANSI 150#; A3: ANSI 300#A6: ANSI 600#

-JX JX: J1, J2, J4J1: JIS 10K; J2: JIS 20K; J4: JIS 40K

-TH Thread; DN4…DN50

Accuracy-N 1.5%

-G1 1.0%

■ Model and Selection

Table 1: Model Selection Guidance for Gas Turbine Flowmeter

Model Code: LWQ-D1-100S1SLN-D16-N

Explanation - Converter: battery power mode without output; Diameter: 100mm; Flow range: 20-400 m3/h; Body Material: SS304; Rotor Material: Aluminum Alloy; No Explosion; Connection: DIN PN16 Flange; Accuracy: 1.5%

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 17 -

Nominal Diameter Standard Flow Range (SFR) Extended Flow Range (EFR)

Standard Pressure Rating

(mm) (in.) Code (m3/h) Code (m3/h) (MPa)

25 1 S 2.5 to 25 W 4 to 40

1.6

40 1.5 S 5 to 50 W 6 to 60

50 2S1 6 to 65 W1 5 to 70

S2 10 to 100 W2 8 to 100

65 2.5 S 15 to 200 W 10 to 200

80 3S1 15 to 300

W 10 to 160S2 20 to 400

100 4S1 20 to 400

W 13 to 250S2 32 to 650

125 5 S 25 to 700 W 20 to 800

150 6S1 32 to 650

W 80 to 1600S2 50 to 1000

200 8S1 80 to 1600

W 50 to 1000S2 130 to 2500

250 10S1 130 to 2500

W 80 to 1600S2 200 to 4000

300 12 S 200 to 4000W1 130 to 2500

W2 320 to 6500

400 16 S 400 to 8000 W 260 to 8000

Warning: Precaution for direct sunshine and rain when the meter is installed outside.

Measurable Flow Rate Range:

Note: The flow range as blow is based on operating status; REFERENCE ONLY. Consult the factory if you have special requirement. Refer to the nameplate or certificate for actual flow range.

■ Cautions for Installation

Mounting Positions

Avoid all pipe locations where the flow is pulsating, such as in the outlet side of piston or diaphragm pumps.

Avoid locations near equipment producing electrical interference such as electric motors, transformers, variable frequency, etc.

Install the meter with enough room for future access for maintenance purposes.

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 18 -

Required Lengths of Straight Runs

Flow altering device such as elbows, valves and reducers can affect accuracy. See diagram below for typical flow meter system installation.

Diagram 1. Typical Flow Meter System Installation

The recommended guidelines are given to enhance accuracy and maximize performance. Distance given here are minimum requirements; double them for desired straight pipe lengths.

◾ Upstream: allow a minimum straight pipe length at least 10 times the internal diameter of the

pipe. For example, with the 50mmpipe, there should be 500mm of straight pipe immediately

upstream. Desired upstream straight pipe length is 1000mm.

◾ Downstream: allow a minimum straight pipe length at least 5 times the internal diameter of

the pipe. For example, with the 50mm pipe, there should be 250mm of straight pipe immediately

upstream. Desired upstream straight pipe length is 500mm.

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 19 -

Diameter (mm) L (mm) Thread

Criteria

25 170 G 2”

40 140 G 2”

50 150 G 2-1/2”

Special Notice

¨ Foreign material in the liquid being measured can clog the meter’s rotor and adversely affect accuracy. If this problem is anticipated or experienced, install screens to filter impurities from incoming liquids.

¨ To ensure accurate measurement, drain all air from the system before use.

¨ When the meter contains removable coverplates. Leave the coverplate installed unless accessory modules specify removal. Don’t remove the coverplates when the meter is powered, or electrical shock and explosion hazard can be caused.

■ Connections

Thread Connection

Note: Default Thread is Male G Thread, other thread are available on request. For example: Female NPT Thread, Male NPT Thread; Consult FLOWNICS for more information

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 20 -

ANSI Flange Meter Dimensions

Size Code A ANSI Flange Rating Class

Flange Diameter

(B)

Bolt Hole Diameter

Bolt Circle Diameter

(PCD)

Bolt Hole Quantity

(inch) (mm) (mm) (mm) (mm) (mm)  

1" 25 170 150 108 16 79 4

  300 124 19 89 4

1-1/2" 40 200 150 127 16 99 4

  300 155 22 114 4

2" 50 200 150 152 19 121 4

  300 165 19 127 8

2-1/2" 65 240 150 180  19  140  4 

  300 190  22  149 8 

3" 80 240 150 191 19 152 4

  300 210 22 168 8

4" 100 300 150 229 19 191 8

  300 254 22 200 8

5" 125 240 150 255  22  216  8 

  300 280  22  235  8 

6" 150 450 150 279 22 241 8

  300 318 22 270 12

8" 200 500 150 343 22 298 8

  300 381 25 330 12

10" 250 500 150 460.4 25 362 12

300 444.5 28.4 387.3 16

12" 300 300 150 482.6 25.4 431.8 12

300 520.7 31.8 450.9 16

Flange Connection

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 21 -

DIN Flange Meter Dimensions

Size Code A DIN Flange Pressure Rating

Flange Diameter

(B)

Bolt Hole Diameter

Bolt Circle Diameter

(PCD)

Bolt Hole Quantity

(inch) (mm) (mm) MPa (mm) (mm) (mm)  

1" 25 170 1.6 115 14 85 4

1-1/2" 40 200 1.6 150 18 110 4

2" 50 200 1.6 165 18 125 4

2-1/2" 65 240 1.6 185 18 145 4

3" 80 240 1.6 200 18 160 8

4" 100 300 1.6 220 18 180 8

5" 125 240 1.6 250 18 210 8

6" 150 450 1.6 285 22 240 8

8" 200 500 1.6 340 22 295 12

10" 250 500 1.6 405 26 355 12

12" 300 300 1.6 460 26 410 12

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 22 -

KOTM 터빈유량계는 미소 유량 측정을 위한 것으로 고온 고압의 조

건 하에서 매우 높은 정확도를 갖는다. 전자 신호 출력이 가능하여

1%의 정확도 및 반복성 0.2%를 유지할 수 있습니다.

Mini flow meter is based on turbine theory and designed for

measuring micro-flow. This meter has extremely high accuracy

especially under the condition of high temperature and high

pressure.

The Electronic pulse transmitter is also integrated in this mini flow

meter. it can maintain the 1% accuracy and the 0.2% repeatability.KOTM

MODEL KOTM-1 KOTM-2

Flow Range

(Diameter)

1.1mm 2.1 ~ 90 L/hr

1.2mm 3.06 ~ 108 L/hr

1.4mm 5.04 ~ 138 L/hr

1.5mm 5.58 ~ 150 L/hr

Accuracy ± 1.5 % ± 1 %

Repeatability 0.25 %

Display No Yes

Signal Output Pulse 4~20 mA

Power Supply +24VDC±15%

Material

Housing : Green Brass

Bearing : Stainless Steel

Rotor : PVDF

Magnet : Ceramin

Seal Ring : MVQ

Protection Level IP 60 IP 65

Diameter 1.1mm~1.5mm

Temperature -10℃~+100℃

Pressure Rating 2MPa

Connection G 1/4 Thread Female

Dimension 55 * 40 * 47 mm

KOTM SERIES

■ Technical Specification

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 23 -

KOTK-24 터빈유량계는 전자부분과 기계부분이 조합된 제품이며

체적식 디젤 기어 유량계입니다.

높은 정확도와 작은 사이즈의 제품으로 유지 관리 또한 쉽습니다.

These flow meters are electromechanical, volumetric flow diesel

gear flow meter.

High Accuracy easy maintenance compact size.

Inlet and Outlet NPT 1”, BSP 1”

Body Material PPS

Flow Range 5~50 GPM (18.9~190 LPM)

Accuracy ±0.5%

Repeatability Error 0.1%

Pressure Class 10Bar

KOTK-24 SERIES

■ Specifications

- High accuracy, Duarble, Compact

- Easy maintenance

- Two cumulants (resetting, and accumulating)

- Gallon or Liter Opetion

- PPC Body

- Also for chemical industry, medicine and other corrosive medium measurement.

■ Technical Specification

Turbine Flow Meter

인천비전기업 / 인천유망중소기업 / 한국발전 기자재공급업체

(주) 플 로 우 닉 스

T E L : 82-32-579-2999

E-MAIL : [email protected]

- 24 -

KOTW 터빈유량계는 높은 정확성과 내구성을 갖춘 소형 사이즈의 제

품으로 출력 모듈을 사용할 수 있습니다. 장거리 전송 및 디스플레이

설정이 간단하며 조립 및 유지보수가 용이합니다. 리튬전지는 9천 시

간동안 전원을 제공합니다.

High accuracy, Durable, Small volume turbine flowmeter, Module

design can be used with output module. sensor and long-distance

transfers, The features of the display : 2 cumulants (1 resetting, 1

accumulating); optional unit conversion of Gallon and Liter. It is

easy to change the spare parts inside, and easy to maintain. It is

easy to assemble as its compact design. Lithium battery, can

supply 9000hours power.

MODEL WLL1 WLL40

Threaded Joint of the Inlet and Outlet NPT 1”, BSP 1” NPT 1.5”, BSP 1.5”

Material Aluminum

Flow Range 5~50 GPM (18.9~190 LPM) 10~100 GPM (38~380 LPM)

Accuracy ±1.0% ±0.5%

Repeatability 0.1%

Pressure Class 300PSI / 21BAR

Material of Connected Parts

Body Aluminum

Bearings Ceramics

Shaft Tungsted Carbide

Rotor PVDF

Supposed Filter Dimension 55 mesh

KOTW SERIES

■ Technical Specification